Mortar ultrafin permeabil pe baza de var MAPEI Mape-Antique FC Ultrafine

Limba: Engleza

87 afisari

Tip documentatie: Fisa tehnica

Pagina 1 - Mortar ultrafin permeabil pe baza de var MAPEI Mape-Antique FC Ultrafine Fisa tehnica...

ee un iq fi t a n tr -AUl e p C a F M EN 998-1 IN COMPLIANCE WITH EUROPEAN STANDARD EN 998-1 GP-CS II RENDERING AND PLASTERING MORTAR Salt-resistant, transpirant ultrafinetexture skimming mortar, based on lime and Eco-Pozzolan, for a smooth finish on render EMICODE® GEV Some application examples • mooth finishing internal/external large-grained, S de-humidifying, macro-porous render when repairing masonry deteriorated by the presence of capillary rising damp and soluble salts. • mooth finishing large-grained dehumidifying render S on masonry in lagoon areas or close to the sea. • mooth finishing new de-humidifying render or old S lime-based render on stone, brick, tuff and mixed masonry, including on buildings of historical and artistic interest with a conservation order or under the protection of the National Trust. • mooth finishing large-grained transpirant or S “structural” base render. formulation developed in MAPEI’s research laboratories. This pr

Pagina 1-Mortar ultrafin permeabil pe baza de var MAPEI Mape-Antique FC Ultrafine Fisa tehnica Engleza ee
un
...

Pagina 2 - Mortar ultrafin permeabil pe baza de var MAPEI Mape-Antique FC Ultrafine Fisa tehnica...

oduct is classified as GP according to EN 998-1 Standards: “General purpose mortar for internal/external render”, category CS II. When mixed with water in a suitable clean container, Mape-Antique FC Ultrafine forms a salt-resistant, smooth, transpirant skimming mortar with a plastic consistency which is easy to apply with a flat metal trowel on both vertical surfaces and on ceilings. The properties of mortar made from Mape-Antique FC Ultrafine, such as mechanical strength, modulus of elasticity and vapour permeability, are very similar to skimming mortar made using lime, lime-pozzolan or hydraulic lime originally used in the construction of old buildings. Compared with these types of mortar, however, Mape-Antique FC Ultrafine also has properties which make the product resistant to various chemical-physical aggressive phenomena, such as the presence of soluble salts, freeze-thaw cycles, the leaching action of rainwater, alkali-aggregate reactions and the formation of cracks caused b

Pagina 2-Mortar ultrafin permeabil pe baza de var MAPEI Mape-Antique FC Ultrafine Fisa tehnica Engleza oduct ...

Pagina 3 - Mortar ultrafin permeabil pe baza de var MAPEI Mape-Antique FC Ultrafine Fisa tehnica...

y plastic shrinkage. Typical values are shown in the Technical Data table (see Application Data and Final Performance sections) which refer to the main characteristics of Mape-Antique FC Ultrafine at both the fresh and hardened states. TECHNICAL CHARACTERISTICS Mape-Antique FC Ultrafine is a pre-blended, ultra finegrained, cement-free skimming mortar in powder form made from lime, Eco-Pozzolan, natural sand and special additives with very low emission of volatile organic compounds (EMICODE EC1 R Plus), according to a RECOMMENDATIONS • Mape-Antique FC Ultrafine is not recommended for structures with high flows of capillary rising damp or high concentrations of soluble salts (we recommend using Mape-Antique FC Grosso or products from the Silexcolor or Silancolor ranges). WHERE TO USE Ultra fine-grained, macro-porous, de-humidifying skimming mortar for repairing masonry deteriorated by the presence of capillary rising damp and soluble salts, including on existent buildings of histo

Pagina 3-Mortar ultrafin permeabil pe baza de var MAPEI Mape-Antique FC Ultrafine Fisa tehnica Engleza y...

Pagina 4 - Mortar ultrafin permeabil pe baza de var MAPEI Mape-Antique FC Ultrafine Fisa tehnica...

rical and artistic interest. Ultra-fine skimming mortar for transpirant or “structural” base render. Ultra-fine skimming mortar for lime-based render deteriorated by the action of atmospheric agents and environmental conditions or by ageing. 617_mape antique fc ultrafine_gb (25.10.2012 - 1ª Bozza/Corr. PDF) ue tiq fine n a e-AUltr p Ma FC Spread on a first layer of Mape-Antique FC Ultrafine Part of application cycle for Mape-Antique FC Ultrafine Smoothing over the product with a flat metal trowel • Mape-Antique FC Ultrafine must be applied in layers max. 1 mm thick for each coat. • Do not use Mape-Antique FC Ultrafine for casting into formwork (use Mape-Antique LC mixed with aggregates with a suitable grain size). • Do not use Mape-Antique FC Ultrafine to make consolidating slurry for injection into structures (use Mape-Antique I or Mape-Antique F21). • Do not use Mape-Antique FC Ultrafine for rendering. • Never add additives, cement or other binders (li