Placaje HPL pentru fatade si pereti interiori - Curatare si intretinere TRESPA METEON

Limba: Engleza

32 afisari

Tip documentatie: Fisa tehnica

Pagina 1 - Placaje HPL pentru fatade si pereti interiori - Curatare si intretinere TRESPA METEON...

TECHNICAL DOCUMENTATION Cleaning and maintaining This document is intended to provide general recommendations only. Trespa provides these guidelines and all testing, code and design data for informational purposes only and strongly advises that the customer, project owner and architect seek independent advice from a certified construction professional and/or engineer regarding application and installation as well as compliance with design requirements, applicable codes, laws and regulations, and test standards. Please check your local codes and applicable design requirements for proper use. General Trespa® Meteon® has a closed surface that is virtually pore-free making it highly impenetrable to contamination. In addition, Trespa® Meteon® is highly resistant to a large number of chemicals including many different non-aggressive and aggressive cleaning agents. Although Trespa® Meteon® requires minimum maintenance, it is advisable to clean the panels after installation on site an

Pagina 1-Placaje HPL pentru fatade si pereti interiori - Curatare si intretinere TRESPA METEON Fisa tehnica...

Pagina 2 - Placaje HPL pentru fatade si pereti interiori - Curatare si intretinere TRESPA METEON...

d at yearly intervals or whenever the windows are being cleaned thereafter, depending on the area, type of application and the care taken with processing and assembly. Dirt prevention Design considerations The effect of dirt on decorative panels varies depending on the cause. An even layer of dust, for instance, is less obvious than streaks or patches caused by rainwater running off and leaving concentrated deposits of dust and dirt. Various construction solutions exist to prevent concentrated dirt marks e.g. by ■ applying fitting overhangs with water deflecting edges; ■ using flat-headed fast-fixing screws for Trespa® Meteon®; ■ ensuring that joints do not occur above the centre of another panel. Construction considerations Some dirt is bound to be generated during construction, but unnecessary soiling should be avoided: ■ remove any labels or stickers immediately after installation; ■ apply adhesives and mastic accurately; ■ mask panel edges while frames are

Pagina 2-Placaje HPL pentru fatade si pereti interiori - Curatare si intretinere TRESPA METEON Fisa tehnica...

Pagina 3 - Placaje HPL pentru fatade si pereti interiori - Curatare si intretinere TRESPA METEON...

being painted; ■ remove severe stains such as paint, cement or tar immediately. Cleaning and repairing Trespa® panels may not just be affected by dust, dirty handprints or algae growth. More serious problems such as soot coating, stubborn graffiti or accidents on site may occur. A wide range of special cleaning agents specifically for these types of staining are available through third parties. Do not use cleaning agents with abrasive or polishing components. Only use clean sponges, soft nylon brushes or cloths and avoid brushes with hard rigid bristles. Always follow the manufacturer’s instructions closely. Recommended concentrations and soaking times should not be exceeded. Good cleaning results will depend on how well the polyurethane, silicone or other polymers, do not dissolve, making them very difficult to remove. Incomplete removal or removal with an unsuitable product may create a permanent film on the panels. This residue may cause an uneven discolouration of the surfa

Pagina 3-Placaje HPL pentru fatade si pereti interiori - Curatare si intretinere TRESPA METEON Fisa tehnica...

Pagina 4 - Placaje HPL pentru fatade si pereti interiori - Curatare si intretinere TRESPA METEON...

ce. Trespa’s warranties do not apply in case of improper or incorrectly performed cleaning. For the use of any cleaning agent, please consider (national) safety and environmental regulations. EN-GB3064 ■ Version 3.1 ■ Date 07-2023 contamination dissolves under the influence of the cleaning agent used. Some products, such as 2-component paint systems, 2 Please check www.trespa.info for the latest version of this document Shoe-polish, crayons, pencil and chalk Even stubborn marks such as shoe polish and children’s crayons are easy to clean from panels using an organic solvent. Rinse the panels with water and wipe to prevent streaks. Location codes written in pencil or chalk and those which are exposed to the weather for long periods of time are more difficult to remove. Paint Remove solvent based paint with an organic solvent. Rinse or wipe the panels to avoid streaks. Remove two-component paint immediately with water and/or an organic solvent. Once this type of paint h